Showing results: 331 - 345 of 602 items found.
-
C350 -
GME Technology
This is a high quality digital capacitance meter. Check the accuracy and status of capacitors up to 20mF, a very handy tool for virtually any technician. It features high accuracy (0.5%) and 9 selectable ranges. A zero adjustment knob is also provided to "zero" test lead capacitance. Includes test probe set and yellow rubber boot.
-
3701 -
Peaceful Thriving Enterprise Co Ltd
*2 x 6m retractable test leads.*Used as an extension cord for cars, trailers, boats and more.*Optional accessory included alligator clips, test probes and banana plugs.*The tester can be used with any multi meter or device equipped with banana jack connectors.*Embedd A Magnet on the back to fix on suitable metal sheet of cars easily.
-
Shenzhen Chuangxin Instruments Co., Ltd.
It’s used to test the mechanical integrity of product enclosures and check the durability of enclosures for electrical appliances of other electrical appliances and other electronic products. If damage occurs from the Impact Hammer test, accessibility probes can be used to measure the extent or severity of the damage. The Impact Hammer simulates the mechanical impact to which electrical equipment maybe subjected.
-
MP-50 -
FRANKONIA GmbH
The Current Monitoring probes may be used whenever RF current measurements are required. Current measurements are made by placing a current carrying conductor within the “sensing” window of the probe and measuring the probe’s output voltage with an RF detector. Calibration of the probe permits the conversion of the voltages measured to current. Current measurements can be made over the frequency range shown in the transfer impedance curve furnished with each probe. There is virtually no loading of the circuit and the technique permits normal operation of the device under test during measurements. The MP-50 can be used for the procedure for clamp injection when the common- mode impedance requirements cannot be met given in chapter 7.4 of IEC/EN 61000-4-6 „Immunity to conducted disturbances, induced by radio frequency fields”. The MP-50 can also be used as current monitor for BCI testing as per ISO11452-4, RTCA/DO-160 section 20, MIL-STD-461 and various automotive standards.
-
QTOUCH1202C -
Qmax Test Technologies Pvt. Ltd.
he Prober Test System is capable of movement in XYZ directions with fixed angle (θ) and dual probe heads (further expandable up to 4 ) . The system has in-built Vision Camera for easy monitoring of probe needle contact.The prober supports automatic fiduciary recognition. The system has built –in linear encoders to achieve higher precision. It also comes with in-built image processing unit with minimum 5 Mega pixel Camera ,tele-centric lens with image processing software, illuminated with LED bar light with controls.The V-I signature test shall be in-built in the Prober system with “ Best fit Curve “ algorithm .Provision for adding various external Test & Measurement instruments like GPIB / USB / PXI Instruments is available.
-
V250 / V250PXI -
Qmax Test Technologies Pvt. Ltd.
V250 / V250PXI is designed as a Combination Board Tester capable of testing highly complex and dense PCBs employing various test techniques on a single platform. It can perform Board Level Functional Test through edge connectors of a PCB, and guided probe diagnostics utility to reliably repair Digital/Analog and Mixed Signal PCBs of various complexities and conventional PCBs. An In –Circuit device test by configuring Pin Drivers to High Current Pin Driver mode and interface to the UUT either through Clips / Probes or nail bed and on board clock disable HW feature are the all time favorite . The in-built high frequency 14bit Analog Driver / sensors synchronized with digital drivers for covering analog / mixed signal devices with high degree of accuracy.
-
MPI Probe Card Technology
The FCB Probe Card is the most mature technology of buckling beam probe card. It is aimed to achieve the semiconductor ship manufacture time-to-market (TTM) and cost of test (COT) demand. FCB is a proven solution for a variety of semiconductor production tests from early engineering pilot-runs to high volume manufacturing (HVM). FCB is ready for device requiring high signal integrity probing (SI) and/or power integrity probing (PI). Applications include cutting-edge SiPs/SoCs, WLP, graphic processors, micro processor, industrial microcontrollers, and more. FCB guarantees the world’s best overall cost-of-ownership (COO) for various DUT applications.
-
CP150-6M -
Teledyne LeCroy
Teledyne LeCroy current probes are available in a variety of models for a wide range of applications. The full range of Teledyne LeCroy current probes includes models with bandwidths up to 100 MHz, peak currents up to 700 A and sensitivities to 1 mA/div. Teledyne LeCroy current probes are often used in applications such as the design and test of switching power supplies, motor drives, electric vehicles, and uninterruptible power supplies.
-
CP030-3M -
Teledyne LeCroy
Teledyne LeCroy current probes are available in a variety of models for a wide range of applications. The full range of Teledyne LeCroy current probes includes models with bandwidths up to 100 MHz, peak currents up to 700 A and sensitivities to 1 mA/div. Teledyne LeCroy current probes are often used in applications such as the design and test of switching power supplies, motor drives, electric vehicles, and uninterruptible power supplies.
-
H71002400 -
6TL Engineering
The 6TL24 is the Base platform ideal for Combinational test (ICT+FCT) in low to mid volume, high-mix electronics productions. A dual-stage pushing mechanism will allow performing both, the FCT and the ICT test, without the need of changing the test platform and with a low cost fixturing technology. To do so, the exchangeable cassette fixture must be designed with two-level probes. IN the 6TL24, the second level is reached thanks to a pneumatic actuator.
-
ProntoTEST-FIXTURE -
Unisoft Corp.
In minutes the Unisoft ProntoTEST-FIXTURE software translates CAD and Bill of Materials (BOM) files into real reference designators, netlists, X/Y component pin geometries, values, tolerances, part numbers, etc. This data is then used by Test Engineers to program their ATE (Agilent/Hewlett Packard "board & board x/y", Teradyne "ipl", Genrad ".ckt"), MDA, and flying probe test equipment and design the "Bed of Nails" test fixtures.
-
HS6-DIFF-500XMS-W5 -
TEAM SOLUTIONS, INC.
The only oscilloscope in the world that has:- SafeGround, differential input channels that can be switched to single ended.SureConnect, auto-detects a true connection between the probe tip and the device under test.- CMI interface.- USB 3.0 interface, 5Gb/s data transfer- Lowest noise
-
HS6-DIFF-50XMS-W5 -
TEAM SOLUTIONS, INC.
The only oscilloscope in the world that has:- SafeGround, differential input channels that can be switched to single ended.SureConnect, auto-detects a true connection between the probe tip and the device under test.- CMI interface.- USB 3.0 interface, 5Gb/s data transfer- Lowest noise
-
APD-ANNUNCIATOR -
Amperis sl
The APD-ANNUNCIATOR is a remote partial discharge detection equipment inside any energized cabinet. The probe is installed in the unit under test, instantly reporting its status. This equipment gives a great benefit because it avoids long term damage to the switching equipment.
-
Chroma ATE Inc.
Chroma offers precision instruments such as laser drivers, photodetector monitoring, and temperature controllers. These lab class instruments are often intefrated into production solutions for wafer probe test, burn-in and device or module characterization with inspection, metrology, robotics, Industry 4.0 and more.